Jenn-Air JJW2830DB Installation Guide download pdf (Page 6)

Electrical Requirements

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine

that the ground path and the wire gauge are in accordance

with local codes.

Check with a qualified electrical installer if you are not

sure the oven is properly grounded.

This oven must be connected to a grounded metal, permanent

wiring system.

Be sure that the electrical connection and wire size are adequate

and in conformance with the National Electrical Code, ANSI/

NFPA 70-latest edition or CSA Standards C22.1-94, Canadian

Electrical Code, Part 1 and C22.2 No. O-M91-latest edition,

and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

Electrical Connection

To properly install your oven, you must determine the type

of electrical connection you will be using and follow the

instructions provided for it here.

■ Oven must be connected to the proper electrical voltage and

frequency as specified on the model/serial/rating plate. The

model/serial/rating plate is located under the control panel on

single ovens and under the control panel on the upper oven

cavity on double ovens. See the following illustrations.

■ Models rated from 7.3 to 9.6 kW at 240 volts (5.4 to 7.4 kW

at 208 volts) require a separate 40-amp circuit. Models

rated at 4.8 kW and below at 240 volts (3.6 kW and

below at 208 volts) require a separate 20-amp circuit.

■ A circuit breaker is recommended.

■ Connect directly to the circuit breaker box (or fused

disconnect) through flexible, armored or nonmetallic

sheathed, copper cable (with grounding wire). See

“Make Electrical Connection” section.

■ Flexible conduit from the oven should be connected

directly to the junction box.

■ Fuse both sides of the line.

■ Do not cut the conduit. The length of conduit provided

is for serviceability of the oven.

■ A UL listed or CSA approved conduit connector must

be provided.

■ If the house has aluminum wiring, follow the

procedure below:

1. Connect a section of solid copper wire to the ends

of the flexible conduit leads.

2. Connect the aluminum wiring to the added section

of copper wire using special connectors and/or tools

designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended

procedure. Aluminum/copper connection must conform

with local codes and industry accepted wiring practices.

For power requirements for models JJW2430D, JJW2427D,

JJW2830D, JJW2827D, JJW2730D, JJW2727D, JJW3430D

and JJW3820D, refer to the following table.

Single Oven

A. Model/serial/rating plate

Double Oven

A. Model/serial/rating plate

240 VAC 208 VAC

Model Watts Amps Watts Amps

JJW2430D

JJW2427D

4141 17.8 3145 15.6

JJW3430 4193 18.3 3193 16.1

JJW2830D

JJW2827D

8279 35.7 6288 31.2

JJW3820D 8363 36.6 6386 32.1

JJW2730D

JJW2727D

8221 34.3 6230 30.7

1 2 3 4 5 6 7 8 9 10 11 ... 31 32

Comments to this Manuals

No comments

Jenn-Air JJW2830DB Installation Guide Page 6

Comments to this Manuals

Related products and manuals for Unknown Jenn-Air JJW2830DB