Jenn-Air W10242571A User Manual download pdf (Page 6)

Undercounter Installation

NOTE: Proper installation is your responsibility. Make sure you have everything necessary for correct installation. It is the personal

responsibility and obligation of the customer to contact a qualified installer to assure that electrical installation meets all national and

local codes and ordinances.

Tools needed:

Gather the required tools and parts before starting installation.

IMPORTANT:

■ Do not grasp control panel to move compactor.

■ To avoid damaging floor covering, slide compactor onto

cardboard or hardboard before moving compactor across

floor.

■ Do not allow the rear frame of the compactor to touch the

floor covering when lifting or moving compactor.

Undercounter Installation

1. Measure the height of your cabinet opening. The top of the

compactor should be at least

¹₈" (3 mm) from the top of the

cabinet opening.

The rear wheels are preset for a cabinet opening of 34¹⁄₄"

(87 cm). See Position “1” in the picture following.

To adjust for other cabinet opening heights:

■ Loosen self-tapping screw enough to clear stud from hole

in Position “1.”

■ Move the rear wheel and stud to Position “2” or “3” as

needed for your cabinet opening measurement:

Position “2”: 34¹⁄₄" to 34⁷⁄₁₆" (87 to 87.5 cm)

Position “3”: 34⁷⁄₁₆" to 34⁵⁄₈" (87.5 to 88 cm)

NOTE: To level the compactor in position “3,” you may

need to add shims under the leveling legs.

■ Tighten screw. Repeat for other rear wheel.

2. Use pliers to lower leveling legs away from cabinet. Adjust

legs so there will be a ¹⁄₈" (3 mm) to ¹₄" (6.4 mm) space

between the top of the compactor and the top of the cabinet

opening. Stand the compactor upright.

3. Move the compactor close to its final location.

4. Plug into a grounded 3 prong outlet.

5. Determine whether you want the compactor frame or drawer

front flush with the cabinet front.

Using the two #8-18 x ⁵₁₆" (8 mm) screws, install the retaining

brackets to cabinet top as needed:

■ If the compactor frame is to be flush with the cabinet

front, place retaining bracket screws through “1.”

■ If the compactor drawer front is to be flush with the

cabinet front, place retaining bracket screws through “3.”

■ If the compactor is to be midway between “1” and “3,”

place the retaining bracket screws through “2.”

6. Slowly lift the front slightly and roll compactor into the cabinet

opening.

Using the two #8-18 x ¹₂" (12 mm) screws, fasten the

retaining brackets to the countertop with the mounting

screws.

Countertop Mounting

If brackets cannot be attached to the underside of

countertop, attach mounting clips to brackets. Fasten

compactor to cabinet front with mounting screws through

mounting clips.

■ Level ■ Phillips No. 2 screwdriver

■ Tape measure ■ Flat-blade screwdriver

■ Pliers ■ ⁵⁄₁₆" Box-end wrench

■ Scissors ■ Utility knife

A. Wheel bracket assembly

B. Cabinet

C. Locating stud

D. Self-tapping screw (pivot)

A. Countertop

B. Retaining bracket

A. Countertop

B. Retaining bracket

C. Mounting screw

1 2 3 4 5 6 7 8 9 10 11 ... 27 28

Comments to this Manuals

No comments

Jenn-Air W10242571A User Manual Page 6

Comments to this Manuals

Related products and manuals for Trash Compactor Jenn-Air W10242571A